WVM Series Large Flow Low Energy Vacuum Regenerated Compressed Air Dryer

Low energy large flow industrial compressed air dryers providing flow rates up to 7300m³/h @ 7 barg with a dew point of -40°C (-20°C and -70°C options). Energy savings of up to 25%.
Parker Generation 5 WVM compressed air dryers provide an energy efficient heat regenerated compressed air drying solution for large scale compressed air applications. Ideal for electronics and automotive production plants but suitable for all general manufacturing industries where typically high volume flows and low pressure dewpoints are required.
Providing energy savings of up to 25% compared to conventional systems, WVM series compressed air dryers can be equipped with heat exchangers that allow steam or other available process heat sources to be used for heat regeneration. This alternative regeneration process can be employed in addition to or instead of the standard electrical heaters, resulting in even higher energy savings.

• Flow Rate: 450 to 7300 m3/hour at 7 barg, 265 to 4297 CFM at 102 psig
• Pressure Dew Point: Standard: -40°C (-40°F) , Options: -70°C (-100°F) or -20°C (-4°F)
• ISO Grade: Standard: Class 2.2.2
• Options: Class 2.1.2 or Class 2.3.2
• Operating Pressure: 4 to 11 barg, 58 to 145 psig
• Operating Temperature: 5 to 40 °C, 41 to 104 °F
• Ambient Temperature: 40.0 °C Maximum, 104.0 °F Maximum
• Electrical Requirements: Standard: 400V 3ph 50Hz Options on request.
• Port Size: DN 50 to DN 150
• Connection Type: Flanged
• Ingress Protection Rating: IP54 Indoor Use Only
• Options: High Performance Insulation for PDP <-40°C
• Specifications Met: PED 2014/68/EU Fluid Group II
• Noise Level: 80 to 85 dBA
• Height: 2029 to 3450 mm, 80 to 137 inch
• Width: 1222 to 2782 mm, 48.0 inch, 110.0 inch
• Depth: 1219 to 2010 mm, 48 to 79 inch
• Weight: 770 to 5380 Kg (1698 to 11863 lbs)

HDK Series High Pressure Compressed Air Dryer (up to 50 bar g)

For applications requiring high pressure compressed air or nitrogen gas up to 50 barg (725 psig) with volume flows up to 1180m³/h (695 cfm)and pressure dew point options of -25, -40°C and -70°C.
The Parker HDK 50 bar range of high pressure compressed air dryers are designed to dry compressed air and gaseous nitrogen at high pressure levels of up to 50 bar reliably and efficiently to multiple pressure dew point options of -40°C, -25°C and -70°C (-40°F, -13°F and -94°F). HDK series dryers come equipped with integrated Parker pre- and after filtration and are capable of volume flows up to 1180 m³/h @ 50 bar g, 35°C (695 cfm @ 725 psi g, 95°F).
Typical applications for HDK series high pressure compressed air dryers are in power stations (i.e. start up of diesel generators) as well as marine applications (i.e. tank ventilation, rope tensioning on off-shore rigs, generator start up etc.).

• Maximum Flow Rate: 50 to 1180 m³/hr @ 50 bar g, 35°C (29 to 695 cfm @ 725 psi g, 95°F)
• Maximum Operating Pressure: 50 barg, 725 psig
• Maximum Ambient Temperature: 50 °C
• Minimum Ambient Temperature: 1 °C
• Ingress Protection Rating: IP65
• Maximum Operating Temperature: 50 °C, 122 °F
• Minimum Operating Temperature: 25 °C, 77 °F
• Connection Type: BSP-P
• Weight: View part number for details.
• Width: View part number for details.
• Depth: View part number for details.
• Height: View part number for details.
• Electrical Requirements: 230V, 50-60Hz, others on request
• Minimum Operating Pressure: 8 barg, 116 psig
• Pressure Dew Point: -40°C, -25°C & -70°C (-40°F, -13°F & -94°F)
• Specifications Met: PED, others on request

KE-MT Series Large Flow Heatless Compressed Air Dryer

Large flow heatless compressed air dryers with available flow rates up to 6100m³/h @ 7 barg and pressure dew points of -25°C to -70°C, for industrial compressed air treatment applications.
Parker KE-MT Series heatless adsorption dryers are designed to supply high quality dry compressed air reliably and efficiently down to a pressure dew point of -70 °C. They are capable of volume flows of up to 6100m³/h at operating conditions of 7 barg (100psig).
The KE-MT Series is offered with energy saving dew point dependent switching (DDS) as an option. Where an application calls for a unit able to cope with variations in operating pressure and load, the installation of a dew point sensor at the outlet of the dryer is available. In such an operating mode, the changeover cycle between vessels only takes place when required, and is dependent on the required dew point being achieved. Only upon reaching this adjustable set dew point, does changeover to the regenerated vessel occur. This feature enables the drying phase to be lengthened and thus avoids the unnecessary use of purge air for regeneration and consequently provides significant energy savings.

• Maximum Flow Rate: 706 to 3590 CFM at 101 psig, PDP -13°F
• Maximum Operating Pressure: 10 barg, 145 psig
• Maximum Ambient Temperature: 50 °C
• Minimum Ambient Temperature: 1.5 °C
• Ingress Protection Rating: IP65
• Maximum Operating Temperature: 50 °C, 122 °F
• Minimum Operating Temperature: 25 °C, 77 °F
• Port Size: DN50 to DN125
• Connection Type: Flanged according to EN1092-1
• Weight: 640 to 2850 kg
• Width: 1060 to 2160 mm
• Depth: 840 to 1565 mm
• Height: 2080 to 2820 mm
• Electrical Requirements: 230V, 50-60Hz
• Controller Type: Multitronic
• Minimum Operating Pressure: 5 barg, 72.52 psig
• Power Consumption: 7.2 VA
• Product Type: Heatless
• Pressure Dew Point: -25 to -70 °C, -13 to -97 °F
• Specifications Met: PED 97/23/EG Module D+B Category II, others on request

Heatless Desiccant Air Dryer – TW Series

Parker Airtek TW Series Heatless Twin Tower Desiccant Air Dryers remove contaminants in compressed air systems using Pressure Swing Adsorption (PSA) technology. Pressure dewpoint of -40°F (-40°C) and flowrate of 10 – 6000 scfm depending on model.
Parker Airtek TW Series Heatless Desiccant Air Dryers remove water vapor from compressed air through a process known as Pressure Swing Adsorption. A standard pressure dewpoint of -40°F (-40°C) is attained by directing the flow of saturated compressed air over a bed of desiccant.
The most commonly used desiccant is activated alumina, a spherical shaped, hygroscopic material, selected for its consistent size, shape and extreme surface to mass ratio. This physically tough and chemically inert material is contained in two separate but identical pressure vessels commonly referred to as “dual” or “twin” towers.
As the saturated compressed air flows up through the “on line” tower, its moisture content adheres to the surface of the desiccant. The dry compressed air is then discharged from the chamber into the distribution system.
A solid state controller automatically cycles the flow of compressed air between the towers, while the “on line” tower is drying, the “off line” tower is regenerating. Regeneration, sometimes referred to as purging, is the process by which moisture accumulated during the “on line” cycle is stripped away during the “off line” cycle. As dry low pressure purge air flows gently through the regenerating bed, it attracts the moisture that had accumulated on the surface of the desiccant during the drying cycle and exhausts it to the atmosphere.

• Connection Type: 3/8 NPT, 1/2 NPT, 3/4 NPT, 1 NPT, 1 1/2 NPT, 2 NPT, 3 FLG, 4 FLG, 6 FLG
• Width: 19 to 96 inch, Consult Factory inch
• Maximum Operating Pressure: 150, 135
• Maximum Operating Temperature: 120 °F
• Weight: 108 to 8300 lb
• Optional Accessories: Pre and After Filter
• Maximum Flow Rate: 17 to 10194.06 m3/hour
• Maximum Inlet Pressure Rating: 100 psi
• Minimum Operating Pressure: 80 psi
• Minimum Operating Temperature: 50 °F
• Maximum Ambient Temperature: 120 °F
• Minimum Ambient Temperature: 40 °F
• Purge Pressure Rate: 2 to 900
• Height: 44 to 113 inch
• Installed Condensate Drain Type: Timed Drain, Consult Factory
• Depth: 14 to 60 inch

FBP HL Medium Flow Heatless Compressed Air Dryer System

FDA approved medium flow compressed air treatment systems, providing flow rates up to 300 m³/hr @ 7 barg. Suitable for food, beverage and pharmaceutical compressed air applications.
The Parker FBP (Food, Beverage, and Pharmaceutical) compressed air dryer system provides compressed air treatment with innovative technology and features which deliver 100% validated air quality and world leading standards of efficiency.
Based upon the OFAS platform, the FBP compressed air dryer system adds FDA approval and improved air quality to ensure food beverage and pharmaceutical standards are achieved.
The centre of any compressed air treatment solution is the dryer, its purpose, to remove water vapour, stop condensation, corrosion and in the case of adsorption dryers, inhibit the growth of micro-organisms. Compressed air contamination problems can be simply avoided by installing a Parker FBP high efficiency compressed air dryer system. The packages are suitable for use with any compressor type and are suited to point of use applications.

• Operating Pressure: 4 to 16 barg, 58 to 232 psig
• Weight: 91 to 232 Kg (201 to 511 lbs)
• Flow Rate: 55 to 300 m3/hour at 7 barg, 32 to 177 CFM at 102 psig
• Ingress Protection Rating: IP55 Indoor Use Only
• Noise Level: < 75 dBA
• Depth: 512 to 682 mm, 20.2 to 27 inch
• Port Size: 1/2 to 1-1/2 inch
• Ambient Temperature: 55.0 °C Maximum, 131.0 °F Maximum
• Connection Type: BSPP or NPT
• Height: 1133 to 2105 mm, 45 to 83 inch
• Operating Temperature: 41 to 122 °F, 5 to 50 °C
• Width: 22 inch, 559 to 630 mm
• Electrical Requirements: Standard: 85 – 265V 1ph 50/60Hz, Optional: 24V DC
• Pressure Dew Point: Standard: -40°C (-40°F) , Options: -70°C (-100°F) or -20°C (-4°F)
• Specifications Met: PED 2014/68/EU Fluid Group II
• ISO Grade: Standard: Class 1.2.0, Options: Class 1.1.0 or Class 1.3.0

CDAS HL Medium Flow Heatless Compressed Air Dryer System

Medium flow compressed air treatment systems providing pressure dew points of -70°C, -40°C or -20°C at flow rates up to 300 m³/hr @ 7 barg. Suitable for all industrial compressed air applications.
Parker’s CDAS HL Clean Dry Air Systems provide clean, dry compressed air in accordance with all editions of ISO8573-1, the international standard for compressed air quality. They are energy efficient and can provide pressure dewpoints of -70°C, -40°C or -20°C with flow rates up to 300 m³/hr (177 cfm) @ 7 barg (102 psi g).
Clean, dry air improves production efficiency and reduces maintenance costs and downtime. Many products claim to provide this, however only CDAS HL Clean Dry Air Systems provide the highest levels of dry compressed air with validated performance.

• Flow Rate: 55 to 300 m3/hour at 7 barg, 32 to 177 CFM at 102 psig
• Pressure Dew Point: ‘Standard: -40°C (-40°F)
• Options: -70°C (-100°F) or -20°C (-4°F)
• ISO Grade: Standard: Class 2.2.2
• Options: Class 2.1.2 or Class 2.3.2
• Operating Pressure: 4 to 16 barg, 58 to 232 psig
• Operating Temperature: 5 to 50 °C, 41 to 122 °F
• Ambient Temperature: 55.0 °C Maximum, 131.0 °F Maximum
• Electrical Requirements: Standard: 85 – 265V 1ph 50/60Hz, Optional: 24V DC Not Applicable for ATEX Models
• Port Size: 1/2 to 1-1/2 inch
• Connection Type: BSPP or NPT
• Ingress Protection Rating: IP55 Indoor Use Only
• Specifications Met: PED 2014/68/EU Fluid Group II
• Noise Level: < 75 dBA
• Height: 1133 to 2105 mm, 45 to 83 inch
• Width: 559.0 mm, 22 inch
• Depth: 490 to 682 mm, 19 to 27 inch
• Weight: 76 to 210 Kg (168 to 463 lbs)

OFAS HL Medium Flow Oil Free Heatless Compressed Air Dryer System

Medium flow compressed air treatment systems with oil vapour removal, providing ISO 8573-1 Class 0 air at flow rates up to 300 m³/hr @ 7 barg. Suitable for all industrial compressed air applications.
Compressed air contamination problems can be simply avoided by installing a Parker OFAS HL Oil Free Air System (including OIL-X filtration). The fully integrated heatless compressed air dryer and filtration packages are suitable for use with any compressor type and can be installed in the compressor room or at point of use.
Fitted with a third adsorbent column for oil vapour removal, Parker’s OFAS HL Clean Dry Air Systems have been third party validated by Lloyds register to provide ISO 8573-1 Class 0, with respect to total oil from both oil lubricated and oil free compressors, ensuring the highest quality air at the point of use for critical applications.
Clean, dry, oil free air improves production efficiency and reduces maintenance costs and downtime. Only OFAS HL Oil Free Air Systems can provide the highest levels of clean, dry, oil free compressed air with validated performance.

• Flow Rate: 55 to 300 m3/hour at 7 barg, 32 to 177 CFM at 102 psig
• Pressure Dew Point: Standard: -40°C (-40°F) , Options: -70°C (-100°F) or -20°C (-4°F)
• ISO Grade: Standard: Class 2.2.0
• Options: Class 2.1.0 or Class 2.3.0
• Operating Pressure: 4 to 16 barg, 58 to 232 psig
• Operating Temperature: 5 to 50 °C, 41 to 122 °F
• Ambient Temperature: 55.0 °C Maximum, 131.0 °F Maximum
• Electrical Requirements: Standard: 85 – 265V 1ph 50/60Hz
• Optional: 24V DC
• Port Size: 1/2 to 1-1/2 inch
• Connection Type: BSPP or NPT
• Ingress Protection Rating: IP55 Indoor Use Only
• Specifications Met: PED 2014/68/EU Fluid Group II
• Noise Level: < 75 dBA
• Height: 1133 to 2105 mm, 45 to 83 inch
• Width: 559.0 mm, 22 inch
• Depth: 512 to 682 mm, 20.2 to 27 inch
• Weight: 90 to 232 Kg (198 to 511 lbs)

Blower Purge Heat Reactivated Desiccant Air Dryer -TWB Series

Parker TWB Series Externally Heated Blower Purge Desiccant Air Dryers use heat and the adsorption method to remove moisture from compressed air. Pressure dewpoint of -40°F (-40°C) and flowrate of 200 – 7500 scfm depending on model.
Compressed air is polluted with dirt particles, water, oil, oil vapor, and condensate. These contaminants result in high maintenance costs, premature wear, spoiled products and the failure of control systems.
Parker TWB Series Blower Purge Desiccant Air Dryers will effectively remove these contaminants. The traditional adsorption principle used in this design is simple, robust and flexible using compressed air for regeneration therefore eliminating any need for an outside energy supply. Continuous drying is accomplished by the operation of two desiccant towers.
Compressed air is dried through one tower while the other desiccant tower is being regenerated. The regeneration heating cycle of the desiccant is accomplished using a hot air flow delivered by an atmospheric blower and external electric heater (other means of heating are optional). The regeneration cooling cycle is performed using a small flow of dry compressed air taken from the blower purge dryer outlet to ensure dewpoint performance. High levels of reliability are achieved by the use of proven engineering technology and components.

• Connection Type: 1” NPT, 1 1/2” NPT, 1 1/2″ NPT, 2″ NPT, 3″ Flg, 4″ Flg, 6″ Flg, 8″ Flg
• Maximum Flow Rate: 170 to 15291 m3/hour
• Maximum Inlet Pressure Rating: 100 psi
• Maximum Operating Pressure: 150, 135
• Minimum Operating Pressure: 80 psi
• Maximum Operating Temperature: 120 °F
• Minimum Operating Temperature: 50 °F
• Maximum Ambient Temperature: 120 °F
• Minimum Ambient Temperature: 50 °F, 40 °F
• Purge Pressure Rate: 0
• Weight: 1050 to 24890 lb
• Width: 49 to 146 inch, Consult Factory inch
• Depth: 27 to 92 inch
• Height: 83 to 114 inch

EcoDry Blower Purge Desiccant Air Dryers

Parker EcoDry Blower Purge Desiccant Air Dryers use the adsorption method to remove moisture from compressed air. Nominal pressure dewpoints down to -40°C (-70°C as option) by directing the flow of saturated compressed air over a bed of desiccant.
Parker EcoDry, EDB dryers contain 2% purge air type and zero purge air type. 2% purge air type dryers combine heat with either a small portion of the dried compressed air or with forced ambient air to affect regeneration. Zero purge air type dryers only use ambient air to affect regeneration. The heated, low pressure air flows gently through the regenerating bed, adsorbing the moisture that accumulated on the surface of the desiccant during the drying cycle and exhausting it to the atmosphere.

• Maximum Operating Pressure: 10 barg
• Maximum Ambient Temperature: 50 °C
• Ingress Protection Rating: IP54
• Maximum Fluid Temperature: 50, 25, 35 °C
• Cooling Method: Air, Chilled Water, Cooling Water
• Port Size: DN50, DN80, DN100, DN150, DN200, DN65, DN250
• Electrical Requirements: 380 V / 3ph / 50Hz
• Height: 2350, 2700, 3000, 3100, 3650, 3550 mm
• Width: 2200, 2000, 2650, 3150, 3600, 3810, 4700, 4350, 4850, 2500, 3410, 5000, 7500 mm
• Depth: 1280, 1450, 1600, 2000, 2100, 2050, 2500, 2750, 3150, 1500, 1550, 2250, 2900, 3500, 3600 mm
• Weight: 2040, 2590, 2865, 3750, 4480, 5550, 6895, 8585, 9815, 12045, 13090, 2250, 2850, 3150, 4200, 4950, 6150, 7590, 9455, 10800, 13250, 14400, 21300 kg
• Specifications Met: GB150, other certificates or approvals on request

Regenerative Desiccant Dryers – P3TJA (3-20 SCFM)

P3TJA Series Heatless Regenerative Desiccant Dryers are ideal for critical, high quality, oil free air treatment applications where very dry air is required. These dryers typically provide pressure dew points of -40°F (-40°C) down to -100°F (-73°C) pressure dew point (pdp). Beneficially, a pressure dew point of -15°F (-26°C) or better will not only prevent corrosion, but will also inhibit microorganisms within the compressed air system. Heatless adsorption or desiccant dryers remove moisture by passing air over a regenerative adsorbent material which strips moisture from the air. This process is known as Pressure Swing Adsorption.

Dryers of this type are extremely efficient and provide typical pressure dew points of -40°F (-40°C) or -100°F (-73°C) pdp. This means that for water vapor to condensate into a liquid, the air temperature would have to drop below -40°F (-40°C) to -100°F (-73°C) respectively. Note that the actual air temperature after an adsorption dryer is not the same as its dew point. The desiccant material is contained in two separate but identical pressure vessels, commonly referred to as “twin” towers. As the saturated compressed air flows up through the “on line” tower, its moisture content adheres to the surface of the desiccant. The dry compressed air is then discharged from the chamber into the distribution system. An onboard solid state controller automatically cycles the flow of compressed air between the towers. While the “on line” tower is drying, the “off line” tower is regenerating. Regeneration, sometimes referred to as purging, is the process by which moisture accumulated during the “on line” cycle is stripped away during the “off line” cycle. As low pressure dry purge air flows gently through the regenerating bed, it attracts the moisture that had accumulated on the surface of the desiccant during the drying cycle and exhausts that moisture laden air to atmosphere.

Functions:

• Mounting Foot: mounting holes, optional wall bracket
• Mounting : 3/8″
• Primary Voltage: 120V/1ph/60Hz
• Flow SCFM: 3 to 20
• Flow m³/min: .085 to .57
• Approximate Purge: 15%
• Maximum inlet or ambient air temperature: 122°F or 50°C
• Maximum Pressure: 175 psi or 21 bar
• Minimum Pressure: 58 psi or 4 bar
• Certifications Designed in accordance with ASME VIII Div.1; CSA / UL / CRN approved; CE Marked (PED, EMC, LVD); IP66 / NEMA 4
• Dew point Range: -40°F or -40°C
• Features Coalescing pre-filter and after-filter included; electronic control timer; fixed LED display for service indication (12,000 hours continuous use) easily serviced IP66 / NEMA 4; integrated desiccant cartridges
• Weight: 24 to 62lbs or 11 to 28kg

Compressed Air Dryers, PSA Desiccant

Model 75-A20 regenerative PSA desiccant dryer reduces the atmospheric dewpoint of compressed air to -100°F (-73°C) without operator attention.
This regenerative dryer has safe, 12 VDC electrical controls. To install, simply attach the inlet (60 psig/4.1 BARG minimum) and outlet air lines, plug the electrical transformer into a wall outlet – no electrician required – and the unit is ready for trouble-free operation. This reliable dryer can be easily installed, operated, and maintained by personnel not trained in instrumentation. The dryer is useful when air comes into contact with moisture-sensitive materials, or when outside compressed air lines are subjected to sub-freezing temperatures.

• Dew Point: -100 °F, -73 °C
• Port 1 Size: 1/4 inch
• Connection Type: NPT Female
• Maximum Operating Pressure: 125 psig, 8.6 barg
• Minimum Operating Pressure: 60 psig, 4.1 barg
• Width: 15 inch, 38 cm
• Height: 41 inch, 104 cm
• Depth: 8.19 inch, 20.8 cm
• Weight: 50 lb, 23 kg
• Maximum Operating Temperature: 78 °F, 25 °C
• Product Type: Pressure Swing Adsorption
• Electrical Requirements: 120VAC / 60Hz
• Compatible Element: 100-18-DX, 100-18-BX
• Drain: Included

Compact Inline Desiccant Dryers – DD15, DD30, DD60 Series

The DD15, DD30 and DD60 inline desiccant dryers should be used for intermittent and not continuous use applications. Always place a bulk separator, particulate and coalescing filter upstream of the desiccant dryer. Desiccant coated with oil will not absorb oil and will render it useless. A check valve should also be installed at the dryer inlet to maximize the life of the desiccant. (Note: that desiccant must be ordered separately.) These compact inline desiccant dryers are a convenient and cost effective means of ensuring your sensitive intermittent pneumatic applications are not exposed to damaging moisture. As wet air enters through the inlet, the air travels down through a bed of desiccant which absorbs the water vapor and aerosols. The silica gel desiccant beads will reduce the humidity down to a -40°F ( -40°C) pressure dew point. After the moisture has been removed, the dry air passes through a sintered bronze filter element (eliminating desiccant dust downstream), up the tube and out the outlet port. As the desiccant becomes saturated with moisture, the dew point will begin to rise. This is evident when the green silica gel desiccant beads in the onboard sight glass change to orange, indicating the need for desiccant replacement. Simply remove the flange and bowl and replace with new desiccant.

• Dryer Type: Inline Desiccant
• Body Material: Aluminum | Steel
• Port Type: NPT | BSPP
• Port Size: 1/4″ | 3/8″ | 1/2″ | 3/4″ | 1″
• Maximum Flow Capacity (SCFM): 15 – 60
• Operating Pressure Range: 0 to 300 psi / 0 to 20.6 bar
• Operating Temperature Range: 32° to 180°F / 0° to 82°C
• Dew Point: -40°F or -40°C
• Desiccant Type: Silica Gel
• Desiccant Capacity (lbs.): 2.5 – 10
• Filter Element (μm): 90 | 40
• Weight Full (lbs.): 10.5 – 30
• Weight Full (kg): 4.8 – 13.6

PoleStar Smart-E (PSE) Series Cycling Compressed Air Refrigeration Dryers – 60Hz & UL Listed

Energy saving refrigerated compressed air dryers effecitve in removing water vapor, down to levels in accorance with ISO8573-1, from compressed air flow rates between 325-6000 scfm while maintaining industry leading low operating costs.
Compressed air systems inherently suffer from performance and reliability issues, most of which can be directly attributed to water in one form or another. In fact, water accounts for up to 99.9% of the total liquid contamination found in a compressed air system. Therefore, air treatment is essential for manufacturing facilities reliant on compressed air for automation.
For general purpose or non-critical use of compressed air, refrigeration dryers are an ideal choice. Refrigeration dryers utilize a closed loop cooling system to lower the temperature of the compressed air to just above freezing, causing condensation of water vapor.
Most of the condensed liquid is then removed by an integral water separator and drained away. Prior to leaving the dryer, the compressed air is re-heated by the incoming compressed air to prevent condensation on the outside of the downstream distribution piping.
Refrigeration dryers should always be installed with general purpose and high efficiency coalescing filters and are an effective way to reduce water vapor, liquid water and water aerosols for general purpose compressed air applications.
Parker’s PoleStar Smart-E (PSE) dryers are the most environmentally friendly refrigeration dryers available. Designed to work with low Global Warming Potential (GWP) refrigerant, R513A, PSE complies with the requirements of the United States Environmental Protection Agency SNAP Rules 20 & 21 and European F-Gas Regulation (EU 517/2014). This makes Parker PSE the best choice to protect your investment, the climate and the environment.

• Electronics Type: ETL Listed
• Weight: 452 lb (205 kg), 463 lb (210 kg), 573 lb (260 kg), 578 lb (262 kg), 582 lb (264 kg), 838 lb (380 kg), 926 lb (420 kg), 1609 lb (730 kg), 1698 lb (770 kg), 1874 lb (850 kg), 2359 lb (1070 kg), 2668 lb (1210 kg)
• Ingress Protection Rating: IP44, IP54
• Maximum Operating Temperature: 149.0 °F, 65.0 °C
• Minimum Operating Temperature: 41.0 °F, 5.0 °C
• Maximum Operating Pressure: 203.0 psig, 14.0 barg
• Depth: 45.3 to 99.6 inch, 1150 to 2529 mm
• Maximum Ambient Temperature: 122.0 °F, 50.0 °C
• Product Type: Refrigeration
• Minimum Operating Pressure: 29.0 psig, 2.0 barg
• Connection Type: NPT-F, ANSI 150#
• Technology: Cycling
• Height: 50.4 to 80.9 inch, 1280 to 2055 mm
• Width: 27.7 to 59.7 inch, 703 to 1517 mm
• Pressure Dew Point: ISO 8573-1 Class 5 for Water
• Refrigerant Type: R-513A
• Port Connection: 2 in, 2.5 in, 4 in, 6 in, 8 in

Refrigeration Dryer Series – PRD10-PRD250 (10-250 SCFM)

PRD Series refrigeration air dryers are ideal for general purpose oil free pneumatic air treatment applications. They typically provide pressure dew points of 35°F (1.7°C) to 50°F (10°C) pressure dew point (pdp). Refrigeration air dryers work by cooling the air, so are limited to positive pressure dew point ratings to prevent freezing of the condensed liquid. Refrigeration dryers use a set of heat exchangers or a single heat exchanger (with chambers) first to pre-cool the air; second to refrigerate the air to condense out moisture vapor; and last to re-heat the air to prevent pipe sweating downstream particularly in humid conditions.

Non-Cycling (Direct Expansion) dryers are a type of dryer where the compressed air and the refrigerant come into direct contact via the heat exchanger. While reliable and simple to use, they generally require that the unit continues to run regardless of actual compressed air flow through the dryer. Cycling dryers that utilize a thermal mass as the means to absorb the heat from the compressed air. By chilling a thermal mass, a refrigerant compressor may turn off in times of low demand thereby saving energy by shutting off the refrigerant compressor.

Functions:

• Pipe Size (in.): 1/2 NPT-F | 3/4 NPT-F | 1-1/2 NPT-F
• Primary Voltage: (V)115 | 230 | 460
• Flow SCFM 10 to 250
• Flow m³/hr. 17 to 425
• Ambient Temperature Range: 41° to 122°F or 5° to 50°C
• Maximum Inlet Temperature: 149°F or 65°C
• Maximum Pressure (psig): 232 (10 – 175 SCFM) | 203 (200 – 250 SCFM)
• Maximum Pressure (bar): 16 (17 -297 m³/hr.) | 14 (425 m³/hr.)
• Pressure drop (psi) @ rated flow Less than 5
• Pressure drop (bar) @ rated flow Less than .35
• Refrigerant: R134A | R407C
• Weight: 42 to 287lb or 19 to 130kg
• Features Non-Cycling; Zero air loss drain; 3-Stage Dew point Indicator; On / Off Switch; PlusPak 3-in-1 aluminum design heat exchanger (patent pending)

SPL Series Refrigerated Dryers

Parker SPL Series Refrigerated Dryers provide volume flow from 0.6 to 5 m³/min with pressure dew points of 3°C to 10°C which ensures continuity and reliability of industrial applications.
The application of high-quality air ensures continuity and reliability of industrial applications, the highest quality standards for finished products and the optimization of production costs.
Parker offers a range of refrigerated air drying solutions using advanced refrigeration technology. Starlette Plus is Parker’s answer to the specific needs of the industrial user.
Starlette Plus safeguards continuous performance and superior efficiency in every industrial compressed air application. It can easily be adapted to suit all working conditions, maintaining reliable dewpoint control and the lowest possible pressure drops and operating costs.
With its state-of-the-art PlusPack heat exchangers (patent pending) and the most compact dimensions of any system in its class, Starlette Plus is the superior choice for any compressed air treatment application.

• Pressure Dew Point: +3 °C, +5 °C, +7 °C Options Available
• Maximum Ambient Temperature: 50 °C
• Maximum Operating Temperature: 65 °C
• Minimum Operating Pressure: 3 barg
• Maximum Operating Pressure: 16 barg
• Port Size: 1/2 to 1-1/2 inch
• Width: 450 to 555 mm
• Height: 430 to 600 mm
• Depth: 210 to 425 mm
• Weight: 19 to 58 kg
• Connection Type: BSPP-F
• Refrigerant Type: R134a

Antares Plus-E Green Hybrid Technology Low Energy Compressed Air Dryer

Green, low energy Hybrid Technology dryers for compressed air applications in industrial and processing markets. Providing volume flows up to 2040 m³/h @ 7 bar g at a dew point of -40°C (-20°C and -70°C options available).
Technical Specifications
Full Product Description
The Antares Plus-E hybrid technology low energy dryer (ATT+ 060-340) is a green and eco-friendly solution integrating the principles of refrigeration and adsorption into a single compact compressed air treatment package, resulting in a highly efficient, economic and low maintenance drying solution, with particular attention to the environment thanks to the use of a low GWP refrigerant (R513A).

Antares Plus-E dryers deliver a cost-effective solution across a wide range of industrial and processing applications. Furthermore, they are especially suited for general purpose applications with external piping: in warmer months, the adsorption dryer can be bypassed to save energy and simply be reinstated in colder months when a refrigeration dryer dewpoint would be insufficient to prevent condensation in external piping.

Features
• Lower GWP refrigerant (R513A), in line with the requirements of the F-Gas regulation.
• Touch screen controller with integrated MODBUS RTU / TCP IP on all sizes.
• Industry 4.0 and IoT ready.
• LED and pressure gauge indicators.
• Improved energy efficiency, thanks to optimized cycling and stand by time.
• Integrated electronic capacitive drain on all models.
• Improved maintenance operation, thanks to data log via USB port. Easier service access, and removable filter insulation.

• Product Type: Compressed Air Dryer
• Product Style: Hybrid
• Product Series: Antares Plus-E
• Flow Rate: 360 to 2040 m3/hour at 7 barg, 212 to 1200 CFM at 102 psig
• Drain: Integrated electronic capacitive
• Options: Bypass Temperature Probe
• Pressure Dew Point: Standard: -40°C (-40°F), Options: -70°C (-100°F) or -20°C (-4°F)
• ISO Grade: Standard: Class 2.2.2, Options: Class 2.1.2 or Class 2.3.2
• Refrigerant Type: R513A
• Operating Pressure: 2 to 12 barg, 29 to 174 psig (ATT+ 060 to 90), 4 to 12 barg (ATT+ 060 to 90), 58 to 174 psig (ATT+ 140 to 340)
• Operating Temperature: 5 to 65 °C, 41 to 149 °F
• Ambient Temperature: 50.0 °C Maximum, 122.0 °F Maximum, ATT 060 – 090: 230V 1ph 50Hz
• Electrical Requirements: ATT 140 – 340: 400V 3ph 50Hz
• Power Consumption: 1.27 to 5.17 kW
• Port Size: 1-1/2 to 2-1/2 inch
• Compatible Prefilter: OIL-X Grades AO and AA Coalescing (Included)
• Compatible After Filter: OIL-X Grade AO Dry Particulate (Included)
• Connection Type: BSPP
• Ingress Protection Rating: IP44 Indoor Use Only
• Specifications Met: PED 2014/68/EU Fluid Group II
• Noise Level: < 75 dBA

Compressed Air Dryers, Membrane -40°F/C Dewpoint

Membrane Compressed Air Dryers, supply clean, dry compressed air with dewpoints as low as -40°F (-40°C).
Membrane Air Dryers combine superior coalescing technology with a proven innovative membrane system to supply clean, dry compressed air with dewpoints as low as -40°F(-40°C), and provide low cost operation with minimal maintenance. Membrane Air Dryers are engineered for easy installation, operation, and long term reliability. Applications include low dewpoint instrument air, pneumatic equipment, pressurizing electrical cabinets, analytical instrumentation, instrument air for analyzer buildings, dry air for hazardous areas, and general laboratory air supply.

• Flow Rate: 1.7, 3.4, 17, 34, 68 m3/hour
• Maximum Ambient Temperature: 120 °F, 49 °C
• Maximum Inlet Pressure Rating: 150 psig, 10.3 barg
• Minimum Ambient Temperature: 40 °F, 4 °C
• Minimum Inlet Pressure Rating: 60 psig, 4.1 barg
• Width: 6 in, 12 in, 19 in
• Height: 22 in, 23 in, 37 in, 39 in
• Weight: 9, 10, 18, 20, 35 lb, 4, 5, 9, 16 kg
• Inlet Port Size: 1/4 NPT female, 1/2 NPT female, 1 NPT female, 1.5 NPT female inch
• Outlet Port Size: 1/4 NPT female, 1/2 NPT female, 1 NPT female, 3/4 NPT female inch
• Operation Type: Steady
• Industry Application: Explosive environments, General industry
• Depth: 5 in, 7 in, 8 in

Compressed Air Dryers for Electrical Cabinets and Enclosures

The meat and dairy industry demands the ultimate in cleanliness and sanitation in its preparation areas. These Cabinet Dryers are designed to purge the inside of the cabinets with very dry air that eliminates moisture and premature component failures.
The meat and dairy industry demands the ultimate in cleanliness and sanitation in their food preparation areas. These areas are washed down nightly. Every square inch of equipment is sprayed with hot (140F), high pressure sanitizers. These sanitizers are caustic or acidic depending on the food. Much of the equipment is pneumatically operated but more and more this industry is moving to electronic controls that are housed in “water-tight” NEMA 4x cabinets. Electrical cabinets eventually develop leaks allowing moisture build up on electronic components. The moisture leads to premature component failure. Premature failure of components leads to emergency service and production down time.

These Dryers are designed to purge the inside of the cabinets with very dry air that eliminates moisture and premature component failures.

Features

• Designed specifically for wash down areas
• Protects electrical cabinet components from damage caused by water and high humidity
• Requires no electricity, low operating costs
• Protects motors, touch screens, drives and other critical components
• Positive pressure keeps dust out
• Adds no heat to the cabinet
• Easy to install and maintain

• Port 1 Size: 1 inch
• Connection Type: NPT
• Maximum Operating Pressure: 150 psig, 10.3 barg
• Minimum Operating Pressure: 60 psig, 4.1 barg
• Width: 3 inch, 4.6 inch, 7.6 cm, 11.7 cm
• Height: 9.2 to 15.3 inch, 7.6 cm, 11.7 cm
• Depth: 2 inch, 2.9 inch, 5 cm, 7.4 cm
• Weight: 1.5 lb, 2 lb, 2.5 lb, 0.68 kg, 0.9 kg, 1.1 kg
• Maximum Ambient Temperature: 120 °F, 49 °C
• Minimum Ambient Temperature: 35 °F, 12 °C
• Dew Point: -7 °F, -22 °C
• Product Type: Membrane
• Electrical Requirements: None
• Compatible Element: 070-063-BX
• Drain: CO2-2392

Compressed Air & Gas – Up to 150 PSIG – FMD Membrane Dryer Series

The FMD Membrane Dryer Series is designed to remove water vapor and aersols at point-of-use for intermittent flows up to 40 SCFM with a +35°F dewpoint and 10 SCFM with a -40°F dewpoint.

Features

• Designed for point-of-use applications
• Pressures to 150 PSIG
• No moving parts
• Drying efficiency down to -40°F pressure dewpoint
• Quiet, Continuous operation
• No electricity needed
• Low pressure drop
• Hollow fiber technology

• Connection Type: NPT
• Maximum Operating Temperature: 40 to 100 °F, 4.4 to 37.8 °C
• Maximum Operating Pressure: 60 to 150 psig, 4.1 to 10.3 barg
• Weight: 0.7 to 13.3 lb, 0.38 to 8.57 kg
• Height: 14.5 to 38 inch, 36.83 to 96.52 cm, 38.1 cm, 55.88 cm, 66.04 cm, 96.52 cm
• Width: 5.5 to 14 inch, 14 to 35.56 cm, 16.51 cm, 25.4 cm, 29.21 cm, 35.56 cm
• Compatible Prefilter Element: 6HM06-013, 6C10-025, 6C10-050